Mather & Sons Pumps Incorporated

The Challenger pressure tank combines high performance and designer appeal. The almond-colored two-part polyurethane paint finish over an epoxy undercoating provides UV and salt spray protection. Efficient and cost-effective, the Challenger pressure tank is designed with a patented controlled action, double diaphragm tank assembly that completely contains storage water in a pre-charged air atmosphere. This air buffer design means fewer problems with condensation.

Challenger tanks have a threaded nut for easy installation of a water pump stand, a stainless steel elbow and an adjustable air charge. Clean, airtight welds are achieved using the most modern welding equipment available.

Our tank diaphragms are constructed with an FDA approved highgrade butyl. Flexcons positive lock internal clench ring system cannot slip and does not rely on the tank wall.  The tank contains a stainless steel port diffuser, and water connection which directs flow upward and outward while locking the lower diaphragm in place.

All of Flexcons quality tanks are backed by a five year written, limited warranty. Challenger tanks are quality tested at four different stages on the production line. Tests include helium and high pressure tests to ensure the structural integrity of every pressure tank.

The Norwesco Underground Pump Tank is made from high density polyethylene and are very corrosion resistant and they are able to be pumped completely empty.  The underground pump tank in 525 gallons and below are spherical tanks and are include a molded in elevated pump stand on the tank bottom.  Raisers are available for all tank sizes in 24 inches high, 15" and 6".  Tanks are available in the following gallons:

300
325
500
525
750
1000
1250
1500
2000
2500

The Norwesco Underground Pump Tank is made from high density polyethylene and are very corrosion resistant. Their pump tank is able to be pumped completely empty and are available in the following gallons:

300
325
500
525
750
1000
1250
1500
2000
2500

The underground pump tank in 525 gallons and below are spherical tanks and are include a molded in elevated pump stand on the tank bottom. Raisers are available for all tank sizes in 24 inches high, 15" and 6".

Storage tanks are often used for bulk storage or mobile nursing applications, but can of coure be used to store almost anything.  Water storage reservoir tanks can maximize system efficiency and smooth demand.  Storage tanks are also a wise investment in emergency prepardness, or standard system down time.  Norwesco offers a wide selection of storage tanks.  Please see our brochures below, or call  ----> 1-800-257-1310

A storage tank is often used for bulk storage or mobile nursing applications, but can of coure be used to store almost anything. Water storage reservoirs can maximize system efficiency and smooth demand.  A storage tank is also a wise investment in emergency prepardness, or standard system down time.  Norwesco offers a wide storage tank selction.  Please see our brochures below, or call now.  ----> 1-800-257-1310

Premium Weight water tanks are thicker and will last longer than light duty tanks.  Shapes include vertical cylinder, PCO, pickup truck, free standing and horizonal leg with optional U bolt tie downs.  The vertical water tanks offer the largest gallonage selections.  Norwesco vertical tanks feature tie-down slots, built-in graduated gallon indicators, an offset fill-opening and a self-vented, slosh-proof lid.  Above ground vertical Norwesco tanks will be provided with a bulkhead fitting installed as standard, but may also be ordered without a fitting or in special sizes.  Premium weight tanks can be special ordered in yellow, blue, dark green or black for a small addition.  Black and dark green in particular keep out light to help prevent water bourne algae growth.  For this reason white potable water tanks may want to be kept indoors out of UV light, but protection from UV light will help all polyethylene tanks last longer.

The Norwesco septic tank and wastewater tank are the industry leader in septic design. Norwesco's septic tank offers superior features including:

-Ease of the septic tank installation
-Rotationally molded one-piece tank construction
-Superior strength design
-Excellent sewage corrosion resistance
-Single or Double compartment design
-Pre-plumbed inlet and outlet fittings. Designed to meet your specific state requirements and ready for installation
-Water tight tank lid
-Full range of septic tank accessories and risers.

The standard weight yellow poly septic tank is suitable for most septic applications. With rocky soil or out of the way installations the Norwesco Bruiser Tank offers heavy duty construction without the need to fill the tank with water during installation.

*Many sizes not pictured - download the full list below or call for sizing information. 1-800-257-1310

Norwesco's septic tanks and wastewater tanks are the industry leader in septic design. Norwesco septic tanks offer superior features including:

-Ease of the septic tanks installation
-Rotationally molded one-piece tank construction
-Superior strength design
-Excellent sewage corrosion resistance
-Single or Double compartment design
-Pre-plumbed inlet and outlet fittings. Designed to meet your specific state requirements and ready for installation
-Water tight tank lid
-Full range of septic tanks, accessories and risers.

Standard weight yellow poly septic tanks are suitable for most septic applications. With rocky soil or out of the way installations the Norwesco Bruiser Tanks offer heavy duty construction without the need to fill the tank with water during installation.

*Many sizes not pictured - download the full list below or call for sizing information. 1-800-257-1310

Norwesco's water cistern burial storage tanks feature a rugged ribbed construction design for excellent durability.  These storage tanks are made from high density polyethylene that meets potable water standards for ANSI tanks and NSF tanks.  The white (natural) color tanks are Norwesco's standard weight potable water cisterns, while the blue bruiser tanks are industry heavy weight reservoirs offering more longevity. 

The spherical 325 and 550 can be used as pump tanks, featuring an integrated pumping stand and the ability to be completely emptied.

Not pictured:

1400 Gallon White (Natural) Water Cisterns

1250 Gallon Bruiser Water Cisterns

1500 Gallon Bruiser Water Cisterns

The Norwesco water cistern burial storage tank features a rugged ribbed construction design for excellent durability.  This style storage tank is made from high density polyethylene and meets ANSI tank and NSF tank standards for potable water.  The white (natural) color tank is Norwesco's standard weight potable water cistern, while the blue bruiser tank is the industry heavy weight reservoir offering more longevity. 

The spherical 325 and 550 can be used as a pump tank, featuring an integrated pumping stand and the ability to be completely emptied.

Not pictured:

1400 Gallon White (Natural) Water Cistern

1250 Gallon Bruiser Water Cistern

1500 Gallon Bruiser Water Cistern

Norwesco vertical water storage tanks are available in either black or dark green.  The dark coloring both helps the tanks blend into nature and prevents light from entering the tanks to discourage algae growth.  Suitable only as water storage tanks they are Norwesco's lightest duty design and offer a cost effective solution as potable water tanks or as irrigation tanks.  All Norwesco water tanks include an ultra violet inhibiter to protect against sun damage and are generally suitable for outdoor use.  Black and dark green water tanks range in size from 305 gallons up to a 10,000 gallon tanks.

Premium weight and Heavy weight water tanks are also available and have additional shape options.

Call now for quick price and availability.  1-800-257-1310

Any Norwesco vertical water storage tank is available in either black or dark green.  The dark coloring both helps the tank blend into nature and prevents light from entering the tank to discourage algae growth.  Suitable only as a water storage tank they are Norwesco's lightest duty design and offer a cost effective solution as a potable water tank or as an irrigation tank.  All Norwesco water tank include an ultra violet inhibiter to protect against sun damage and are generally suitable for outdoor use.  Black and dark green water tank range in size from 305 gallons up to a 10,000 gallon tank.

A Premium weight and Heavy weight water tank is also available and have additional shape options.

Call now for quick price and availability.  1-800-257-1310

Fabricated steel discharge heads for vertical turbine pumps offer several advantages over cast iron discharge heads. Each fabricated head is custom designed to application specifications and has a unique feature set.  For example, fabricated heads for canned turbines feature special centerlined inlets and outlets above grade to connect your piping up to.  Things like sounding tubes and transducer ports can placed exactly where needed. In general fabricated discharge heads are heavier duty than cast discharge heads and will support more weight down the well, and larger motors fixed to the top of them. They are less inclined to cracking. The heavy solid weight of a fabricated discharge head provides a solid support to keep your mission critical pump motor running more smoothly than a lighter cast discharge. While fabricated discharge heads do require longer lead times and more up-front cost on your initial investment, the added features and benefits are often worth the upgrade. Because fabricated discharge heads are custom designed they are also useful to replace cast iron pump discharges that are no long manufactured.

American Marsh OSG ANSI pumps are used in harsh process pump applications in a variety of industrial markets. The OSG series ANSI pumps feature heavy duty castings, oversized shafts, oil lubrication, single row inboard and double row outboard bearings, outboard bearing impeller adjustment and choice of optional metallurgies.

Performance Characteristics:

• Capacities to: 7,000 GPM
• Heads to: 730 Feet
• Temperatures to: 500 F (260 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Back pull-out to reduce maintenance down time. Meets ANSI B73.1 dimensional standards.
• Packed or mechanically sealed stuffing box options to meed aggressive applications.
• Impellers have back pump out vanes to keep the seal chamber free of debris.
• Thrust bearing adjustment to quickly dial back factory running tolerances.
• Oil lubricated bearing housing for superior cooling and extended bearing life.
• Available standard in Ductile Iron/Ductile Iron fitted or other alloy for application versatility.
• High efficiency semi-open impellers designed to handle process fluids.
• 150 lb. ANSI flange suction/discharge connections with centerline discharge and cast integral foot on casing for support. Optional 300 lb. flanges available.
• Sleeved or solid shaft to minimize deflection at stuffing box.
• Wide variety of stuffing boxes to meet application requirements.
• Bearing isolators to keep bearing housing clean and free of contaminents.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh OSD ANSI pumps are used in harsh process applications in a variety of industrial pump markets. The OSD series ANSI B73.1 pumps feature heavy duty castings, oversized shafts, oil lubrication, single row inboard and double row outboard bearings, optional stuffing box cooling jacket, outboard bearing micromillimeter impeller adjustment and choice of optional metallurgies.  Commercial pump applications include: Boiler feed pumps, transfer pumps, and condensate return pumps.  Industrial pump applications include: Propane pumps, butane pumps, crude oil pumps, acid pumps, gasoline pumps, naphtha pumps, organic fluid pumps, petrochemical pumps, black liquor pumps, ammonia pumps, and cargo transfer pumps.

Performance Characteristics:

• Capacities to: 7,400 GPM
• Heads to: 985 Feet
• Temperatures to: 500 F (260 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Back pull-out to reduce maintenance down time. Meets ANSI B73.1 dimensional standards.
• Packed or mechanically sealed stuffing box options for aggressive pumping applications.
• Micromillimeter thrust bearing adjustment to quickly dial back factory running tolerances.
• Optional bearing and stuffing box cooling jackets for higher temperatures.
• Oil lubricated bearing housing for superior cooling and extended bearing life.
• Available standard in Cast Steel/Cast Steel fitted or other alloy for pump application versatility.
• High efficiency reverse vane pump impellers designed to handle process fluids.
• 150 lb. ANSI flange suction/discharge connections with centerline discharge and cast integral foot on casing for support. Optional 300 lb. flanges available.
• Wide variety of stuffing boxes to meet application requirements.
• Single row inboard bearings for rigid shaft support.
• Bearing isolators to keep bearing housing clean and free of contaminents.
• Sleeved or solid shaft to minimize deflection at stuffing box.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh vertical process sump pumps are used in a variety of aggressive applications. These pumps are used in commercial, industrial and municipal applications every day. The SOSM series vertical process pumps feature heavy duty OSD ANSI casings, oversized shafts, short bearing spans, optional metallurgies and lineshaft bearing material flexibility.

Due to the metallurgy available in the 460 Series OSD product line, fluid ends are available in a wide variety of exotic materials. Low Flow OSD models can also be used in the SOSM product offering.

Performance Characteristics:

• Capacities to: 7,400 GPM
• Heads to: 985 Feet
• Temperatures to: 500 F (260 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Heavy duty casings and impellers.
• Available standard in Cast Iron/Iron fitted or other alloy for application versatility.
• Replaceable wearing components include casing wear rings to maintain peak efficiency.
• Reverse vane or semi-open impeller design, hydraulic and dynamic balancing increasing performance and pump life.
• 125 lb. ANSI flange suction/discharge connections.Heavy duty, grease lubricated thrust bearing and oversized lineshaft and inboard head bearings.
• Lineshaft bearings can be supplied in bronze, cast iron, carbon graphite, teflon or metal backed marine material.
• Pump setting flexibility to depths of 25+ feet.
• Optional stuffing box.
• 4 foot to 5 foot maximum lineshaft bearing spans.
• Internal lubrication for flushing lineshaft bearings.
• Optional oil filled support column.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh centrifugal vertical sump pumps are used in a variety of aggressive applications. These pumps are used in commercial, industrial process pumping and municipal applications every day. The SREM series vertical process pumps feature heavy duty casings, oversized shafts, short bearing spans, optional metallurgies and lineshaft bearing material flexibility.

Performance Characteristics:

• Capacities to: 9,000 GPM
• Heads to: 450 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Heavy duty pump casings and impellers.
• Available standard in Cast Iron/Iron fitted or other alloy for application versatility.
• Replaceable wearing components include casing wear rings to maintain peak efficiency.
• Enclosed impeller design, dynamic balancing and renewable wear rings reduce losses increasing performance and pump life.
• 125 lb. ANSI flange suction/discharge connections.
• Heavy duty, grease lubricated thrust bearing and oversized lineshaft and inboard head bearings.
• Lineshaft bearings can be supplied in bronze, cast iron, carbon graphite, teflon or metal backed marine material.
• Pump setting flexibility to depths of 25+ feet.
• Optional stuffing box.
• 4 foot to 5 foot maximum lineshaft bearing spans.
• Internal lubrication for flushing lineshaft bearings.
• Optional oil filled support column.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh vertical end suction inline centrifugal pumps are used in commercial, industrial and municipal applications every day. The REI 310 series end suction products feature back pull out impellers, inline suction and discharge, cast iron integral base on all casings with heavy casing thickness, impellers with back pump out vanes and oversized shafts to provide the end user with a superior, reliable product.

Performance Characteristics:

• Capacities to: 9,000 GPM
• Heads to: 450 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Back pull-out to reduce maintenance down time.
• Standard American-Marsh Series 810 mechanical seal for both reliability and dependability.
• Carbon/Si-Carbide/EPDM elastomers standard, with other faces and elastomers available.
• Integral seal flush.
• Available standard in Cast Iron/Bronze fitted or other alloy for application versatility.
• Replaceable wearing components include casing wear rings to maintain peak efficiency.
• Enclosed impeller design, dynamic balancing and renewable wear rings reduce losses increasing performance and pump life.
• 125 lb. ANSI flange suction/discharge connections with centerline discharge and cast integral foot on casing for support. Suction and discharge flanges are casted to 250 psi dimensions. Case working pressures for all REF models is 250 psi.
• Standard, stocked c-face motors for quick shipment.
• Pumps can be stocked and shipped less driver allowing more flexibility for the end user.
• C-face motor bracket allows the removal of the driver without disassembling entire pumping unit.
• Impellers have back pump out vanes to keep the seal chamber free of debris.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh flex coupled end suction centrifugal pumps are used as general purpose pumps in commercial, industrial and municipal applications every day. The REF series end suction products feature back pull out impellers, centerline discharges, cast integral feet on all casings with heavy casing thickness, impellers with back pump out vanes and oversized shafts to provide the end user with a superior, reliable product.

Performance Characteristics:

• Capacities to: 9,000 GPM
• Heads to: 450 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 3600 to 1200 RPM

Features & Benefits:

• Back pull-out to reduce maintenance down time.
• Standard American-Marsh Series 810 mechanical seal for both reliability and dependability. Carbon/Si-Carbide/EPDM elastomers standard, with other faces and elastomers available.
• Internal seal flush.
• Available standard in Cast Iron/Bronze fitted or other alloy for application versatility.
• Replaceable wearing components include casing wear rings to maintain peak efficiency.
• Enclosed, francis impeller design, dynamic balancing and renewable wear rings reduce losses increasing performance and pump life.
• 125 lb. ANSI flange suction/discharge connections with centerline discharge and cast integral foot on casing for support. Suction and discharge flanges are casted to 250 psi dimensions. Case working pressures for all REF models is 250 psi.
• Optional rigid carbon steel bedplate and OSHA coupling guard.
• Impellers have back pump out vanes to keep the seal chamber free of debris.
• Oil lubricated power frame for cooler bearing operation. All REF pump models feature bearings with a minimum 100,000 hour design life.

AMERICAN MARSH PUMP SELECTION SOFTWARE

American Marsh close coupled end suction centrifugal pumps are used as general purpose pumps in commercial, industrial and municipal applications every day. The REC series end suction products feature back pull out impellers, centerline discharges, cast integral feet on all casings with heavy casing thickness, impellers with back pump out vanes and oversized shafts to provide the end user with a superior, reliable product.

Performance Characteristics:

• Capacities to: 9,000 GPM
• Heads to: 450 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 3600 to 900 RPM

Features & Benefits:

• Back pull-out to reduce maintenance down time.
• Standard American-Marsh Series 810 mechanical seal for both reliability and dependability.
• Carbon/Si-Carbide/EPDM elastomers standard, with other faces and elastomers available.
• Integral seal flush.
• Available standard in Cast Iron/Bronze fitted or other alloy for application versatility.
• Replaceable wearing components include casing wear rings to maintain peak efficiency.
• Enclosed impeller design, dynamic balancing and renewable wear rings reduce losses increasing performance and pump life.
• 125 lb. ANSI flange suction/discharge connections with centerline discharge and cast integral foot on casing for support. Suction and discharge flanges are casted to 250 psi dimensions. Case working pressures for all REF models is 250 psi.
• Standard, stocked c-face motors for quick shipment.
• Pumps can be stocked and shipped less driver allowing more flexibility for the end user.
• C-face motor bracket allows the removal of the driver without disassembling entire pumping unit.
• Impellers have back pump out vanes to keep the seal chamber free of debris.

AMERICAN MARSH PUMP SELECTION SOFTWARE

The GI Internal Gear pumps operate smoothly and with equal efficiency in either direction. They efficiently handle both thin and
thick liquids and are designed for a broad range of applications at various flows and pressures. They are also capable of operating
under a suction lift condition. Pumps are available in several materials of construction with or without relief valves. Pumps can be supplied with conventional packing or mechanical seal. Available with 90 degree ports, which can be rotated in 45 deggree increments.

Performance Characteristics:

• Capacities to: 400 GPM
• Heads to: 462 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 1800 to 500 RPM

Features & Benefits:

• Heavy cast iron gears for long life and durability.
• Packed stuffing box standard. Optional American-Marsh Series 810 mechanical seal for both reliability and dependability. Carbon/Si-Carbide/EPDM elastomers standard, with other faces and elastomers available.
• Large variety of shaft bushings available.
• Optional relief valve.
• Thrust control and adjustable clearances.
• Optional rigid carbon steel bedplate and OSHA coupling guard.

AMERICAN MARSH PUMP SELECTION SOFTWARE

These helical gear pumps operate smoothly and with equal efficiency in either direction of operation when the relief is in the proper position. They efficiently pump heavy, viscous materials such as asphalt, molasses, roofing compounds and printing inks; as well as fuel oils, gasolines and similar thin liquids.

Amercian Marsh gear pumps are available in several materials of construction with or without relief valves. Gear pumps can be supplied with conventional packing or mechanical seal.

Performance Characteristics:

• Capacities to: 400 GPM
• Heads to: 289 Feet
• Temperatures to: 300 F (150 C)
• Speed ranges: 900 to 100 RPM

Features & Benefits:

• Heavy cast iron gears for long life and durability.
• Packed stuffing box standard. Optional American-Marsh Series 810 mechanical seal for both reliability and dependability. Carbon/Si-Carbide/EPDM elastomers standard, with other faces and elastomers available.
• Large variety of shaft bushings available.
• Optional relief valve.
• Optional rigid carbon steel bedplate and OSHA coupling guard.

Our long tradition of quality pump manufacturing began in 1873 making us one of the first pump manufacturers in this country. American-Marsh Pumps provides the user dependability and durability. Durability by design is always the most cost effective solution. Nearly all designs are available in alternate metallurgy constructions.

Heavy Duty Integral Base
• Casted or fabricated steel designed and sized for the pump and its application
• The base can be designed for close-coupled or flexcoupled, shaft driven driver

Shaft Sleeve
• Standard - replaceable bronze sleeve protects shaft from wear and corrosion

Stuffing Box
• When packed, supplied with a bronze lantern ring and gland
• When sealed, supplied with an American-Marsh Series 810 Carbon/Silicon-Carbide/EPDM mechanical seal
• Other component and cartridge seals available on request

Upper Bearing Housing
• Heavy duty deep groove type, double row bearing, purge grease type lubrication standard and is cartridge mounted to permit easy removal of rotating element
• Double row roller bearing is protected by a lip seal to keep contaminates out of bearing housing
• Double row bearing carries both the radial and axial forces generated by the rotating assembly

Heavy Duty Shaft
• Designed and sized especially for the pump and its applications
• 420 stainless steel shaft standard

Drivers
• Assemblies can be close- or flex-coupled engineered to customer specifications

OVERVIEW:

SINGLE PHASE:
■ Single Phase, 6" motors available in 5 - 15 HP, 230 volt models.
■ Require CentriPro Control Boxes as shown on Order Number chart.

THREE PHASE:
■ Three Phase, 6", 5 - 30 HP, 230 and 460 volt models have an exclusive voltage change plug feature.
■ 6 - 10" Three Phase available from 5 - 200 HP in 200, 230, 460 and 575 volt models.

FEATURES:

6" Canned Design Motor Features

• Replaceable Plug-in Motor Lead - All 6" motor leads are stranded copper for flexibility and strength. Leads are 150" long and field replaceable.
• Insulation - The canned motor's stator coil is mounted in a stainless steel frame and is completely sealed in a stainless steel cylinder. The coil wire features moisture resistant insulation which is completely water-proofed for long life.
• Heat Resistant - The space between the stator's stainless steel protective can and its frame is filled with a specially formulated patented resin that protects the motor against thermal fluctuation and internal stress.
• 95º F (35º C) Water Temperature (CANNED TYPE: 6", 5 - 50 HP) - The motors operate with a minimum flow rate of 0.5 ft./sec. (0.15 m/sec) in water temperature up to 95º F (35º C) without any derating of horsepower. This 95º F (35º C) temperature is 18º F (10º C) higher than NEMA standards.

8-10" Rewindable Water-Tight Motor Features

• Insulation Wire - The coil conductor insulation material is a specially developed denatured polypropylene, which offers excellent leak-resistant characteristics. Three barriers are applied to the copper conductors to provide complete insulation against the motor's cooling fluid. This design is the result of extensive research and is of superior quality. It insures that CentriPro motors will have an extremely long service life. Motor Features - Both Designs
• Sand Resistant Slinger and Lip Seals - CentriPro submersible motors feature double-row, grease packed, lip seals to prevent sand from entering the motor. A carbon steel slinger with a baked on epoxy coating prevents sand from entering the lip seal area. Additional protection against sand intrusion is provided by the close tolerance slinger guide with a .02" fit. This design is field-proven in West Texas wells which are considered to be some of the worst sandy well applications. Best of all, these features are standard for a CentriPro motor, so there is no need to stock one motor for clean wells and another more
expensive motor for the more abrasive, sandy jobs.
• High Torque Characteristics - The stator laminations are constructed of high quality, electrical grade, silicon steel which provide high torque even when the motor is subjected to nominal voltage variations.
• Balancing - The rotor balance rings (one on each end of the rotor) allow for excellent dynamic balance for the rotating element of the motor.
• Carbon Sleeve Bearings - Two carbon, water-lubricated, guide bearings are used to properly align the shaft. The bearings have a large surface area to better support the shaft, reducing whipping, while acting as a steady bushing.
• Water-Filled Design - The internal cooling water is mixed with antifreeze and antirust liquid to allow the motor to be stored at -22º F (-30º C). Two water plugs are provided for filling or draining the antifreeze fluid during maintenance. These plugs are also used to top off and to check the water level.
• Complete Corrosion and Water-Tight Protection - All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated carbon steel housings), shaft and bolts. All other motor parts are finished with the baked epoxy coating.
• Baked Epoxy Coating - All external and internal cast iron parts are coated with a baked epoxy resin that provides excellent resistance to water and corrosion.
• Quality Control - All CentriPro submersible motors are manufactured and tested under the most stringent quality control procedures, providing long service life and trouble-free operation.

Quick Disconnect Control Boxes for 4", 1Ø, 3-Wire Submersible Well Water Pump Motors

Features
■ Voltage Relays for installer convenience
■ 115 and 230 volt models
■ 208 volt relay, 9K461, available for low voltage applications
■ Start Capacitors
■ NEMA 3R enclosure for indoor or outdoor mounting
■ Quick disconnect cover design will retrofit with F.E. Q-D control boxes
■ Multiple knockouts
■ Two grounding lugs

Magnetic Contactor 1Ø Well Water Pump Control Boxes
For 3-wire, 1½ - 5 HP Submersible Motors

Features

■ Built-in Magnetic Contactors allow the use of standard pressure switches, prolong switch life and eliminate the need to source and install separate contactors, saving installation time and reducing total system component costs.
■ Voltage Relay for installer convenience
■ 230 volt standard models - 208 volt relay, 9K479 available for low voltage applications
■ Start Capacitors for starting torque
■ Run Capacitors for efficiency and quiet operation
■ Type 3R enclosure for indoor or outdoor mounting
■ Accepts up to #2 AWG wire
■ Multiple knockouts and two ground terminals
■ Manual reset overloads on 1½ - 5 HP models

Capacitor Start - Capacitor Run Control Box for 3-wire, ½ HP - 5 HP Submersible Pump Motors

Features

■ Voltage Relay for installer convenience
■ 230 volt models - 208 volt relay, 9K479, available for low voltage applications
■ Start Capacitors for starting torque
■ Run Capacitors for efficiency and quiet operation
■ Type 3R enclosure for indoor or outdoor mounting
■ Accepts up to #2 AWG wire
■ Multiple knockouts and two ground terminals
■ Higher HP models require heavy duty pressure switches - See Magnetic Contactor version to use standard pressure switches
■ Manual reset overloads on 1½ - 5 HP models

FEATURES

■ 304 SS casing and end bells for corrosion resistance
■ Kingsbury type, 3 shoe, thrust bearing, see chart for ratings
■ Stainless steel, 17-4 PH splined shaft
■ Removable, replaceable motor leads, 48" (½ - 2 HP) or 100" (3 - 7.5 HP)
■ Water lubricated with filter/check valve to maintain fluid fill
■ Lightning and surge protection built-in on 200 V and 230 V models.
■ Magnetic starter with Class 10, quick-trip overload protection required.
■ U.L. 778 Recognized
■ CSA Certified
■ NEMA Mounting Dimensions

Water-Reels® are manufactured by Kifco/Ag-Rain Incorporated, one of the oldest traveling irrigation manufacturers in the U.S.A. With more than 15,000 machines in operation and 40 years in business, Kifco/Ag-Rain manufactures two lines of irrigation systems. Our Ag-Rain Water-Reels® are the larger Agriculture Irrigation Systems, A-Series machines, are used to irrigate larger acreage areas. Kifco Water-Reels® are the smaller Turf Irrigation Systems, B-Series machines, used to irrigate sport complexes, horse arenas and residential sites. If you have any questions, please feel free to contact us. For your portable irrigation system, choose the economical, reliable, easy to operate Water-Reel® made by Kifco, Inc. in Havana, Illinois.

A Premium Weight water tank is thicker and will last longer than a light duty tank.  Shapes include vertical cylinder, PCO, pickup truck, free standing and horizonal leg with optional U bolt tie downs.  The vertical water tank offers the largest gallonage selections.  Norwesco vertical tank features tie-down slots, built-in graduated gallon indicators, an offset fill-opening and a self-vented, slosh-proof lid.  An above ground vertical Norwesco tank will be provided with a bulkhead fitting installed as standard, but may also be ordered without a fitting or in special sizes.  A Premium weight tank can be special ordered in yellow, blue, dark green or black for a small addition.  Black and dark green in particular keep out light to help prevent water bourne algae growth.  For this reason a white potable water tank may want to be kept indoors out of UV light, but protection from UV light will help any color polyethylene tank last longer.

The American-Marsh submersible turbine pump is designed for long, dependable life in many
applications. Modern processing methods require modern pumping equipment to satisfactorily
handle the many and varied fluids used in the various industries. American-Marsh submersible turbine pump engineers,
backed by over 125 years of manufacturing experience, have met this demand with their vertical
turbine pump offered today. They have incorporated in their design, ideas and suggestions from
competent engineers from all sections of the country to produce the best submersible turbine on the market!

The American-Marsh Vertical Turbine pumps are designed for long, dependable life in many
applications. Modern processing methods require modern pumping equipment to satisfactorily
handle the many and varied fluids used in the various industries. American-Marsh Engineers,
backed by over 125 years of manufacturing experience, have met this demand with the vertical
turbines offered today. We have incorporated in our design, ideas and suggestions from
competent engineers from all sections of the country.

AMERICAN MARSH PUMP SELECTION SOFTWARE

Goulds is a major player in submersible turbine pump manufacturing.  Quality control starts immediatly at thier own foundry and continues through a network of professional submersible turbine pump installers.  Features of the Goulds Sumbersible Turbine Pump Include:

■ Discharge Bowl: Several discharge sizes available (NPT).
■ Discharge Bearing: Extra long sealed top bronze bearing insures shaft alignment and stabilization for extended life.
■ Intermediate Bowl: Class 30 cast iron. Glass coating on 6" and larger bowls for maximum effi ciency and abrasion resistance.
■ Intermediate Bearings: Available in either no-lead bronze or rubber.
■ Impellers: Designed for maximum effi ciency with a wide range hydraulic coverage. Made of low zinc and no lead material suitable for drinking water applications.
■ Taperlock: Accurately machined to ensure positive locking of the impeller to the pump shaft.
■ Upthrust Collar: Designed with extra margin of safety against momentary upthrust at start-up.
■ Suction Adapter: Designed to ensure proper pump/motor alignment. Open area permits easy access to pump/motor coupling. Casting made of ductile iron for increased strength.
■ Pump to Motor Coupling: Stainless steel coupling accurately machined for perfect alignment, balance and power transmission.
■ Pump Shaft: 100,000 PSI high tensile type 416 stainless steel provides strength and corrosion resistance. Ground and polished for smooth bearing surface.
■ Powered for Continuous Operation: All horsepower ratings are within the service limits of the motor and the submersible turbine pump can be operated continuously without fear of damage to the motor.

The Goulds short set vertical turbine pump is used in many types of pump applications. Their versatility and durability are why they are installed every day.  Whether in a wet pit pump application or as a canned booster pump, Goulds knows how to make the vertical turbine pump.

Capabilities

• Capacities to 20,000 GPM (4545 m3/hr)
• Heads to 1,500 feet (457 m)
• Bowl sizes from 5" to 30"

Canned Vertical Turbine Pump Design Features

• Product lube or enclosed lineshaft design.
• Cast or fabricated discharge head and flanged or threaded column assembly.
• 416 SS shafting. Other alloys available.
• Standard cast iron bronze fitted construction. Ductile iron, Ni Al brz, 316 SS or other alloys available.
• Taperlock or keyed impeller design.
• Wear rings optional.
• Packing or mechanical seal design.
• Built-in alignment and simple piping for less costly installation and ease of maintenance/reduce downtime.

Services

• Raw Water Intake Pumping
• Pumping Stations
• Cooling Water Pumping
• Commercial/Industrial Pumping
• Municipal Pumping
• Mining Pumps

The Goulds stainless steel vertical turbine pump handles harsh environments that other materials can't!  They are used in versatile pump applications. This versatility and durability are why they are installed every day.  Whether a wet pit pump application, deep water well pump or as a submersible canned booster pump, Goulds knows how to make the vertical turbine pump.

FEATURES

■ Discharge Bowl: Discharge available in NPT thread or flanged.
■ Discharge Bearing: State of the art thermoplastic water lubricated bearing is standard. Bronze greasepacked sealed bearing complete with 316SS plug available on request.
■ Intermediate Bowl: Heavy duty design and investment cast for industry leading durability and efficiency.
■ Impeller: Wide range of hydraulic coverage designed for maximum efficiency.
■ Thrust Washer: Designed with an extra margin of safety against upthrust at start up.
■ Intermediate Bowl Bearing: State of the art thermoplastic sleeve bearings are standard. Self-flushing rubber bearing is available on request.
■ Taper Locks: Precision machined to ensure positive locking of impeller to pump shaft.
■ Suction Inlet: Hydrodynamic design ensures smooth entrance flow. Oversized inlet strainer prevents solids from entering hydraulic assembly.
■ Suction/Motor Adapter: Heavy duty casting designed for strength, corrosion resistance, easy access to pump/motor coupling, and ensure motor alignment.
■ Pump to Motor Coupling: Precision machined and balanced for perfect alignment and power transmission.
■ Pump Shaft: Designed for maximum strength and excellent corrosion resistance. Turn, ground and polish providing a smooth bearing surface.
■ Check Valve: ITT/Goulds Pumps also offer 316 SS check valve with NPT threads.
■ Powered for Continuous Operation: All hydraulic ratings are within the motor power ratings.

Features:

■ 1-1/2" - 10" discharge sizes
■ Capacities to 7000 GPM, 480' TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
■ 150# rated fl at faced fl anges
■ Heavy wall construction
■ Grade 5 capscrews
■ HC75 & HC10 Series- Enclosed impellers, internally hydraulically balanced
■ Double volute on HC10x10-14, for balanced radial forces,HC14 Series- External balance line standard
■ Standard with graphite packing or single mechanical seal

Features:

■ 4 performance ranges - 35, 45, 60 and 90 gpm.
■ Stainless steel discharge head and motor bracket.
■ High fl ow impellers and stages are glass-filled Noryl® for maximum effi ciency.
■ Ceramic shaft sleeve and rubber discharge bearing eliminates sand wear.
■ Intermediate bearing for increased shaft stability.
■ Floating eye and hub seals for improved performance and effi ciency.
■ Stainless steel hex pump shaft, shell and shaft coupling.
■ High capacity upthrust assembly for protection during start-up and operation (45, 60 and 90 gpm models).
■ Powered by Franklin's corrosion-resistant 4" submersible motors.
■ 2" NPT discharge
■ Check valve must be ordered separately.

Ideal for farm, home, irrigation, industry, municipal and commercial applications, equipped with the power, performance and reliability you expect from Franklin Electric. Flow ratings of 50, 75, 100 and 125 gpm with TDH up to 1200 ft. Horsepower ranges from 1-1/2 to 40 hp

Features:

■ Heavy-duty stainless steel discharge head and motor bracket.
■ Stainless steel shaft, shell, intake screen and cable guard provides corrosion resistance and longer pump life.
■ Glass-fi lled Noryl® impeller stage assemblies provide exceptional strength and durability.
■ Ceramic shaft sleeve and rubber discharge bearing minimizes bearing wear and shaft misalignment.
■ 3" NPT heavy-duty stainless steel discharge head.
■ Modular motor bracket enabling 4" or 6" motor mount for 5-10 hp units.
■ One year unconditional warranty against failure from sand locking in abrasive well conditions.

The V6 Booster Pump is ideal for industrial/commercial applications where water pressure boosting is required. Designed with Premium hydraulics for reliability and excellent performance. The V650 is available in 1.5 hp through 7.5 hp models. The V675 is available in 3 hp through 7.5 hp models.

The Turf Boss excels when used to supply water to a timer operated irrigation system, but the rugged, easily serviced pump can be used in other areas as well. Some of which are residential water transfer, commercial dewatering, rainwater drainage, light agricultural irrigation, sump drainage, and industrial liquid transfer. As a premium self-priming sprinkler pump the Turf Boss is approved for indoor or outdoor operation through CSA and UL.  Whether it is a sprinkler system, a construction site, or a water transfer tank, when moving high volumes of water the Turf Boss guarantees the right amount of water right on time.

Flooded suction centrifugal pump suitable for usewith saltwater, chemical transfer, and other pumping applications that deal with corrosive substances.

Features:

■ High tech, non-corrosive plastic construction. All metal components that have contact with liquid are stainless steel.
■ Motor shaft is completely insulated from any contact with pumping liquid.
■ 2" union connections ensure easy service and optimum water flow. Unions must be ordered separately.
■ Discharge port easily rotates to 90 degree increments without removing motor.
■ Lightweight design.

The Franklin 4-inch Super Stainless motor has been the driving force behind residential and light commercial submersible pumps for decades. Designed and patented in 1950 by our founder, Ed Schaefer, this motor has proven to be the industry's most trusted residential pump motor.

Franklin offers 4-inch motors in a full line of single- and three-phase voltages, frequencies, and application-specific models. Wherever there is an independent source of clean groundwater, you can find a Franklin motor. Typical applications that rely on our motors include:

* Homes
* Farms
* Restaurants
* Schools
* Small Factories
* Coalbed Methane Recovery
* Car Washes
* Fountains

Features:

* Corrosion-resistant construction
* Stainless steel splined shaft
* Hermetically-sealed windings
* StatorShield resin system
* Filter check valve
* Water lubrication
* Kingsbury-type thrust bearing
* Pressure-equalizing diaphragm
* Sand fighting slinger
* Built-in lightning arrestors (single-phase)
* New lead assembly
* Franklin-manufactured control boxes available for single-phase motors
* UL 778 recognized (North American voltages)
* CSA certified
* ANSI/NSF 61 certified
* Industry standard NEMA mounting dimensions

Special Options

* 316 SS Construction - Special construction option for corrosive applications, including acids, low pH and seawater.
* SandFighter^TM Construction - Special construction option for sandy water wells. Motors include SandFighter^TM sealing system with silicon carbide mechanical shaft seal and are warranted against sand entry failure.
* Coalbed Methane Construction - Special construction option for coalbed methane wells. Includes Sand Fighter sealing system, reinforced diaphragm housing to resist damage from bottom tagging and protective filter to shield diaphragm from debris.
* Oil Stripper Construction - Special construction option for secondary oil recovery wells where there is a mixture of oil and water. They are also suitable for geothermal and other water well applications where high temperatures and/or high pH conditions exist. Three-phase Oil Stripper motors are equipped with Subtrol heat sensor for use with SubMonitor protection devices.

The outline of a 1950's vertical pump motor and discharge head forms the basis Mather Pumps logo.  We have been dealing with electric vertical pump motors for turbine pumps since our inception, and there's not a more robust type of product available.  When it comes to experience and quality in the electric motor industry, Emerson's U.S. Motors® brand has a proven history of success, particularly with vertical turbine pump motors. With one of the largest installed bases throughout the world, one brand stands alone for vertical electric motors, U.S. Motors®.

MODIFICATIONS AVAILABLE TO HIGH THRUST MOTORS

• Non-Reverse Ballomatic® Ratchet or Self Release Coupling
• Various Coupling Sizes Available at no additional charge
• Multiple Base Sizes Available at no additional charge

MODIFICATIONS AVAILABLE TO INVERTER DUTY
320 FRAME AND LARGER STOCK PRODUCT

• Bearing Resistance Temperature Detectors (RTD)
• 175% Extra High Thrust
• Vibration Switches
• Water Cooling Coils

The outline of a 1950's vertical electric pump motor and discharge head forms the basis Mather Pumps logo.  We have been dealing with vertical pump motors for turbine pumps since our inception, and there's not a more robust type of product available.  When it comes to experience and quality in the electric motor industry, Emerson's U.S. Motors® brand has a proven history of success, particularly with vertical turbine pump motors. With one of the largest installed bases throughout the world, one brand stands alone for vertical electric motors, U.S. Motors®.

MODIFICATIONS AVAILABLE TO HIGH THRUST MOTORS

• Non-Reverse Ballomatic® Ratchet or Self Release Coupling
• Various Coupling Sizes Available at no additional charge
• Multiple Base Sizes Available at no additional charge

MODIFICATIONS AVAILABLE TO INVERTER DUTY
320 FRAME AND LARGER STOCK MOTORS

• Bearing Resistance Temperature Detectors (RTD)
• 175% Extra High Thrust
• Vibration Switches
• Water Cooling Coils

Variable frequency drive pump systems have taken the industry by storm, and we whole heartedly endorse them...but only for the right application. Designing a pump system with a variable frequency drive takes a serious amount of expertise. We never approach drives as one size fits all solutions; instead we are going to evaluate your pumping needs carefully before recommending the costly addition of a variable frequency drive - VFD. You can be sure that when we do recommend a variable frequency drive that it will add value to your pump system, protect your equipment and probably reduce your total cost of ownership. When evaluating drive providers Mather Pumps brings essential and hard to find substance to your project by understanding how complex drives control and affect your critical pump system investment. In addition, a pump variable frequency drive rarely stands on its own.  We are able to integrate them with other important pieces of electrical pump control and safety equipment to make a motor control center specifically for your pump system. Call us today to talk about your variable frequency drive pump project at: 1-800-257-1310

Simflo is a company built around the turbine pump.  Their submersible turbine pump bowls range size from 4" to 28", capable of producing from 5 gallons per minute to 18,000 gallons per minute at up to 1,500' of head. Submersible discharge heads are available with 2" to 12" outlets. Simflo's products can be had in a wide range of materials including cast iron, ductile iron, cast steel, NI-resist, NI-hard, bronze alloys (including aluminum-bronze), stainless steels and heat treated aluminum. Many turbine pump bowl modifications are available, including: wear rings (bronze, aluminum-bronze, 304-316-416 stainless steels, NI-resist, Teflon, ceramic, etc.); grease-packed bearings; hard-chrome plated 416 stainless steel bowl shafting and extra length bearings.

Simflo Online Pump Selection

Simflo's bowls range size from 4" to 28", capable of producing from 5 gallons per minute to 18,000 gallons per minute at up to 1,500' of head. Standard cast iron discharge heads are available with 3" to 10" outlets, fabricated steel heads can be custom configured with 2" to 30" outlets. Submersible discharge heads are also available with 2" to 12" outlets.

Simflo's products can be had in a wide range of materials including cast iron, ductile iron, cast steel, NI-resist, NI-hard, bronze alloys (including aluminum-bronze), stainless steels and heat treated aluminum. Many bowl modifications are available, including: wear rings (bronze, aluminum-bronze, 304-316-416 stainless steels, NI-resist, Teflon, ceramic, etc.); lateral machining for deep settings in excess of 1,000'; grease-packed bearings; hard-chrome plated 416 stainless steel bowl shafting and extra length bearings.

Simflo Online Pump Selection

Well-X-Trol® Tank redefined the pump industry in 1963 with the first pre-pressurized diaphragm well tank; featuring
innovation elements like a sealed air charge and corrosion-proof water reservoir. With proven
performance for nearly five decades, Well-X-Trol Professional Tanks remain the industry’s most trusted brand,
continuing to deliver unparalleled water system reliability. Well-X-Trol Tanks offer unique design features that
provide consistent performance while promoting pump longevity and reduced energy use.

Amtrol Pressure Tank                Residential Pressure Tank       

Industrial Pressure Tank                       ASME Rated Tank

Hot Water Expansion Tank

• Sensitive and Accurate Pressure Control
• Easy Adjustment and Maintenance
• Tamper Resistant
• Optional Check Feature
• Fully Supported Frictionless Diaphragm

The Cla-Val Model 90-01/690-01 Pressure Reducing Valve automatically reduces a higher inlet pressure to a steady lower downstream pressure, regardless of changing flow rate and/or varying inlet pressure. This valve is an accurate, pilot-operated regulator capable of holding downstream pressure to a pre-determined limit. When downstream pressure exceeds the pressure setting of the control pilot, the main valve and pilot valve close drip-tight.

If a check feature is added, and a pressure reversal occurs, the downstream pressure is admitted in the main valve cover chamber, closing the valve to prevent return flow.

Typical Applications

Typical applications include pressure reducing valve station using Model 90-01BY/690-01BY and Model 90-01AS/690-01AS in parallel to handle wide range of flow rates. Larger Model 90-01BY/690-01BY valve meets requirements of peak loads and smaller Model 90-01AS/690-01AS handles low flows.